Файл nxp_base_addresses.h

Базовые Адреса перефирийных устройств в NXP. Подробнее...

Граф файлов, в которые включается этот файл:

См. исходные тексты.

Макросы
#define	LPC_AD0_BASE   0xE0034000
	A/D Converter 0 (AD0) base address.
#define	LPC_AHB_BASE   (0xF0000000UL)
#define	LPC_AHBRAM0_BASE   (0x7FE00000UL) /*Ethernet RAM (16 kB*/
#define	LPC_AHBRAM1_BASE   (0x7FD00000UL) /* USB RAM (16 kB)*/
#define	LPC_APB0_BASE   (0xE0000000UL)
#define	LPC_APB1_BASE   LPC_APB0_BASE
#define	LPC_CAN1_BASE   0xE0044000
#define	LPC_CAN2_BASE   0xE0048000
#define	LPC_CAN_ACCEPT_BASE   0xE003C000
	CAN CONTROLLERS AND ACCEPTANCE FILTER base address.
#define	LPC_CAN_CENTRAL_BASE   0xE0040000
#define	LPC_DAC_BASE   0xE006C000
	D/A Converter base address.
#define	LPC_DYNAMIC_MEM0_BASE   0xA0000000
#define	LPC_DYNAMIC_MEM1_BASE   0xB0000000
#define	LPC_DYNAMIC_MEM2_BASE   0xC0000000
#define	LPC_DYNAMIC_MEM3_BASE   0xD0000000
#define	LPC_EMC_BASE   0xFFE08000
	External Memory Controller (EMC) base address.
#define	LPC_EMC_BASE   0xFFE08000
	External Memory Controller (EMC) base address.
#define	LPC_FIO_BASE   0x3FFFC000
	Fast I/O setup base address.
#define	LPC_FLASH_BASE   (0x00000000UL)
#define	LPC_GPDMA_BASE   0xFFE04000
	General-purpose DMA Controller base address.
#define	LPC_GPDMACH0_BASE   0xFFE04100
	General-purpose DMA Controller channel 0 base address.
#define	LPC_GPDMACH1_BASE   0xFFE04120
	General-purpose DMA Controller channel 1 base address.
#define	LPC_GPIO0_BASE   (LPC_FIO_BASE + 0x00000)
#define	LPC_GPIO1_BASE   (LPC_FIO_BASE + 0x00020)
#define	LPC_GPIO2_BASE   (LPC_FIO_BASE + 0x00040)
#define	LPC_GPIO3_BASE   (LPC_FIO_BASE + 0x00060)
#define	LPC_GPIO4_BASE   (LPC_FIO_BASE + 0x00080)
#define	LPC_GPIO_BASE   0xE0028000
	General Purpose Input/Output (GPIO)
#define	LPC_GPIOINT_BASE   0xE0028080
#define	LPC_I2C0_BASE   0xE001C000
	I2C Interface 0 base address.
#define	LPC_I2C1_BASE   0xE005C000
	I2C Interface 1 base address.
#define	LPC_I2C2_BASE   0xE0080000
	I2C Interface 2 base address.
#define	LPC_I2S_BASE   0xE0088000
	I2S Interface Controller (I2S) base address.
#define	LPC_MAC_BASE   0xFFE00000 /* AHB Peripheral # 0 */
	Ethernet MAC (32 bit data bus) base address.
#define	LPC_MCI_BASE   0xE008C000
	MultiMedia Card Interface(MCI) Controller base address.
#define	LPC_PARTCFG_BASE   0x3FFF8000
#define	LPC_PINSEL_BASE   0xE002C000
	Pin Connect Block base address.
#define	LPC_PWM0_BASE   0xE0014000
	Pulse Width Modulator (PWM) base address.
#define	LPC_PWM1_BASE   0xE0018000
#define	LPC_RAM_BASE   (0x40000000UL)
#define	LPC_RTC_BASE   0xE0024000
	Real Time Clock base address.
#define	LPC_SC_BASE   0xE01FC000
	System Control Block(SCB) base address.
#define	LPC_SPI0_BASE   0xE0020000
	SPI0 (Serial Peripheral Interface 0) base address.
#define	LPC_SSP0_BASE   0xE0068000
	SSP0 Controller base address.
#define	LPC_SSP1_BASE   0xE0030000
	SSP1 Controller base address.
#define	LPC_STATIC_MEM0_BASE   0x80000000
	MPMC(EMC) registers, note: all the external memory controller(EMC) registers are for LPC24xx only.
#define	LPC_STATIC_MEM1_BASE   0x81000000
#define	LPC_STATIC_MEM2_BASE   0x82000000
#define	LPC_STATIC_MEM3_BASE   0x83000000
#define	LPC_TIM0_BASE   0xE0004000
	Timer 0 base address.
#define	LPC_TIM1_BASE   0xE0008000
	Timer 1 base address.
#define	LPC_TIM2_BASE   0xE0070000
	Timer 2 base address.
#define	LPC_TIM3_BASE   0xE0074000
	Timer 3 base address.
#define	LPC_UART0_BASE   0xE000C000
	Universal Asynchronous Receiver Transmitter 0 (UART0) base address.
#define	LPC_UART1_BASE   0xE0010000
	Universal Asynchronous Receiver Transmitter 1 (UART1) base address.
#define	LPC_UART2_BASE   0xE0078000
	Universal Asynchronous Receiver Transmitter 2 (UART2) base address.
#define	LPC_UART3_BASE   0xE007C000
	Universal Asynchronous Receiver Transmitter 3 (UART3) base address.
#define	LPC_USB_BASE   0xFFE0C200
#define	LPC_USB_INT_BASE   0xE01FC1C0
	USB Controller base address.
#define	LPC_USBHC_BASE   0xFFE0C000 /* for LPC24xx only */
	USB Host Controller and OTG registers base address.
#define	LPC_USBOTG_BASE   0xFFE0C100
	USB OTG Controller base address.
#define	LPC_USBOTG_CLK_BASE   0xFFE0CFF0
#define	LPC_USBOTG_I2C_BASE   0xFFE0C300
#define	LPC_WDG_BASE   0xE0000000
	Watchdog base address.
#define	LPC_WDT_BASE   LPC_WDG_BASE
#define	VIC_BASE   0xFFFFF000
	————-SYSTEM ——————————————————–

Подробное описание

Базовые Адреса перефирийных устройств в NXP.

Автор

Dmitriy Cherepanov

Дата

2010

См. определение в файле nxp_base_addresses.h